• Название:

    Рабочие материалы Доустановка монитора и нави...

  • Размер: 1.27 Мб
  • Формат: PDF
  • или
  • Название: E39 Bord_Navi_Anfang

BMW Parts and Accessories
Installation Instructions

INFO
1

4

2

5

3

6

FM

AM

TONE SELECT

MENU

MODE

F 39 0524 B

Retrofit Kit On-board Monitor and Navigation System
BMW 5 Series (E 39)
These installation instructions are only valid for vehicles prior to production date 9/00
which are equipped with OE555 High on-board computer.
Technical and electrical knowledge is required
Installation time approx. 7 hours, which can vary according to the condition and fittings of the
vehicle.
Retrofit/Installation Kit no.: 65 90 0 025 171
65 90 0 027 764

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

Contents
Chapter

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.

15.

16.
17.
18.
19.
20.
21.
22.

Page

Important notes on the installation of the on-board monitor and navigation system ....51
Preparatory work..........................................................................................................52
Parts overview..............................................................................................................53
Connection overview....................................................................................................57
Installation and cabling diagram of the on-board monitor wiring harness ....................61
Installation and cabling diagram of the supplementary wiring harness for
navigation in vehicles prior to production date 9/98 ....................................................62
Installation and cabling diagram of the supplementary wiring harness for
navigation in vehicles from production date 9/98 ........................................................63
Install supplementary speedo A signal in vehicles from production date 9/99,
without speedo A signal at radio connector X18126 ....................................................64
Install on-board monitor wiring harness, on-board monitor and on-board
monitor radio................................................................................................................66
Install supplementary wiring harness for navigation in vehicles prior to
production date 9/98 .................................................................................................. 71
Choose installation of the supplementary wiring harness for navigation in
vehicles from production date 9/98 ............................................................................73
Install supplementary wiring harness for navigation in vehicles from production
date 9/98 (PIN18 and PIN35 at connector of the hydraulic unit ABS not assigned) .... 74
Install supplementary wiring harness for navigation in vehicles from production
date 9/98 (PIN18 and PIN35 at connector of the hydraulic unit ABS assigned) ..........77
Install supplementary wiring harness for navigation in vehicles from production
date 9/98
(PIN18 assigned and PIN35 not assigned at connector of the hydraulic unit ABS) ......79
Install supplementary wiring harness for navigation in vehicles from production
date 9/98
(PIN18 not assigned and PIN35 assigned at connector of the hydraulic unit ABS) ......82
Install navigation system ..............................................................................................85
Coding and finalising operations..................................................................................88
Connection description forTV function ........................................................................90
Circuit diagram, on-board monitor wiring harness........................................................91
Circuit diagram, navigation system wiring harness ......................................................93
Circuit diagram, supplementary wiring harness for navigation system for vehicles
prior to production date 9/98 ......................................................................................95
Circuit diagram, supplementary wiring harness for navigation system for vehicles
from production date 9/98 ..........................................................................................97

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

1.

Important notes on the installation of the on-board monitor and
navigation system

Only for use within the BMW trading organisation.
Installation of the on-board monitor and the navigation system may only be undertaken by a
specialist workshop which has available the necessary special tools and the required manuals
(maintenance, repair, diagnostic, etc.).
When cables/leads are being installed, care should be taken to see that they do not get
kinked or damaged.
Additionally installed cables/leads should if necessary be fastened with cable straps.
Item numbers relate only to the overviews or to the text at the side of the associated
illustration.
All operations are represented as taking place on a left-hand drive vehicle, the identical
logical procedure must be followed for right-hand drive vehicles.
Electrical knowledge is required.
The control cable of the on-board monitor/CD changer does not form part of the
installation kit and, in vehicles with CD changer without DSP amplifier, must be ordered
separately as per the Electronics Parts Catalogue (EPC).
The trim panel in the boot at rear left in front of the navigation computer does not form part of
the installation kit and must be ordered separately as per the Electronics Parts Catalogue
(EPC) to accord with the vehicle equipment
Rights are reserved to make technical modifications.
Required tools and auxiliary materials
MoDIC III or DIS
Set of 1/4 inch socket wrenches
Set of Phillips screwdrivers
Cable lamp
Side-cutting pliers
Silicone

Hot-air dryer
Set of Torx socket wrenches
Set of flat-tip screwdrivers
Multimeter
Phillips screwdriver, short

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/51

2. Preparatory work
TIS AW NO.
Print out error memory
Disconnect battery
Dismantle finisher of instrument panel, centre left
Dismantle finisher of instrument panel, right
Dismantle radio (no longer required)
Dismantle operating unit (no longer required)
Loosen lower part of the trim panel for instrument panel
(as perTIS)
Dismantle function carrier of radio, is to be replaced by function
carrier of the on-board monitor (assembly is described in TIS)
Dismantle trim panel, centre console, front left
Undo centre console, below front left
Dismantle left front seat
Dismantle rear seat bench
Dismantle rear seat back
Dismantle sill strip, left front and left rear
Dismantle lower part of the B-pillar trim panel, left
Fold up carpet on left
Dismantle C-pillar trim panel on left and right
Dismantle rear window shelf
Dismantle left speaker under the rear window shelf
Dismantle boot floor
Dismantle trim panel in boot at rear left
(is to be replaced by new trim panel)
Dismantle trim panel in boot, left
Dismantle trim panel in boot, rear right
Dismantle trim panel of closing panel
Dismantle sill strip at right front and right rear
Dismantle lower part of the B-pillar trim panel, right
Dismantle A-pillar trim panel, lower right
Dismantle glove box
Fold up carpet on right
Dismantle CD changer (if present)
Dismantle bracket for CD changer (if present)
Dismantle bracket for video module (if present)
Dismantle DSP amplifier (if present)
Dismantle bracket for DSP amplifier (if present)

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

12 00 ...
51 45 030
51 45 030
65 11 030
65 12 040

51 16 202
51 16 239
51 16 239
52 17 000
52 24 005
52 24 015
51 47 000/51 47 030

51 43 251
51 46 000
51 47 101
51 47 151
51 47 172
51 46 050
51 47 000/51 47 030

51 16 360
65 11 070

65 11 070
65 11 070

EN/52

2. Preparatory work
In addition for right-hand drive vehicles
Dismantle footwell trim panel under the steering column

TIS AW NO.
-

In addition for vehicles from production date 9/99 without speedo A signal at the radio
connector X18126
Dismantle finisher of instrument cluster
Dismantle instrument cluster

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

-

Date: 10.2000

EN/53

3.

Parts overview

1

2

4

3

5

6

7

8

13

12

9

10

14

11

15

INFO
1

4

2

5

3

6

FM

AM

MODE

16

TONE SELECT

MENU

17

18

19

F 39 0525 B
Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/54

3.

Parts overview

21

20

22

24

25

26

31

32

33

37

38

27

23

29

28

35

34

39

40

30

41

36

42

43

F 39 0526 B
Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/55

3.

Parts overview

1
2
3

On-board monitor wiring harness
Navigation wiring harness
Supplementary wiring harness for navigation system for vehicles prior to production
date 9/98
Supplementary wiring harness for navigation system for vehicles from production
date 9/98
Antenna extension for GPS antenna
GPS antenna
Supplementary cable, speedo A signal
Shrinkage tubing (contained in pack with supplementary cable, speedo A signal)
2-way insulation-piercing connector (contained in pack with supplementary cable,
speedo A signal)
Mounting clip
Support of GPS antenna
Complete on-board monitor
On-board monitor holding pin ( for supporting the on-board monitor)
Function carrier of on-board monitor
Cross-recess fillister head screw M3x8 (4 items)
Cover for on-board monitor
On-board monitor radio
Bracket for DSP amplifier
Base carrier
Bracket of video module, front
Bracket of on-board monitor radio and CD changer
Navigation computer
Bracket of navigation computer
Hex nut with washer M5
Hexagon bolt with washer M5x14 (12 items)
Plug-in nut M5 (7 items)
Hex-head self-tapping screw with washer 4.8x16 (3 items)
Plastic expanding nut 4.8 (3 items)
Plastic cap nut (3 items)
Rubber grommet (2 items)
Bush (for attachment of the bracket of the GPS antenna) (2 items)
Expanding rivet (for attaching the GPS antenna) (2 items)
Disassembly clip (2 items)
Cable strap (20 items)
Cable holder (2 items)
Sealing strip
Shrinkage tubing (contained in pack with supplementary wiring harness for navigation)
(2 items)
Protective strip (2 items)
Butt-joint connector (7 items)* (for cable cross-section 0.2-0.5 mm_)
Butt-joint connector (10 items)*(for cable cross-section 0.75-1.0 mm_)
Butt-joint connector (4 items)* (for cable cross-section 1.5-2.5 mm_)
Tube (20 items)*
Textile tape*

4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43

Parts marked with * are not required.

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/56

4.

Connection overview

A8

A7

A9

A6

A13
A10

A5
A

A14

A4

A3

A11
A12
A15

A2
B

A1

A16

B4
B5
B3
B6
C
B2

C3
C5

C1

B1

C6
C4

C2
D3

D4

D
D5

D1
E

D6
D2
E2

E1
F

F2

F1
F3
F 39 0527 B
Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/57

4.

Connection overview
Cable colour

Connection point in vehicle

On-board monitor wiring
harness

-

-

A1

blue 12-pole socket housing

-

at blue 12-pole pin housing at on-board monitor (12)

A2

white 12-pole socket housing

-

at white 12-pole pin housing at on-board monitor (12)

A3

black 17-pole pin housing

-

at radio connector X18126

A4

coaxial pin housing

black

is installed to installation location of the left TV amplifier
in the C-pillar, left, and tied back

A5

coaxial pin housing

black

is installed to installation location of the right TV amplifier
in the C-pillar, right, and tied back

A6

angled coaxial socket housing

black

is tied back with cable strap to the on-board monitor
wiring harness A

A7

angled coaxial socket housing

black

is tied back with cable strap to the on-board monitor
wiring harness A

A8

black coaxial socket housing
(antenna connection)

black

at coaxial pin housing at on-board monitor radio (17)
(antenna connection)

A9

angled coaxial socket housing

black

at coaxial pin housing at on-board monitor (17)

A10

ring terminal Ø 6 mm

brown

at ground post X13016 at the C-pillar, left

A11

coaxial socket housing

black

at coaxial pin housing at antenna diversity

A12

coaxial pin housing

black

at coaxial socket housing at antenna diversity

A13

black 17-pole socket housing

-

at on-board monitor radio (17)

A14

10-pole socket housing

-

is clipped into black 17-pole socket housing A13 of the
on-board monitor wiring harness A and plugged in with
the black 17-pole socket housing A13 at the on-board
monitor radio (17)

A15

white 6-pole pin housing

-

at branch cable B1, white 6-pole socket housing, of
navigation wiring harness B

A16

blue 18-pole socket housing

-

at blue 18-pole pin housing at navigation computer (22)

Item
A

Designation

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/58

4.

Connection overview

Item

Designation

Cable colour

Connection point in vehicle
-

B

Navigation wiring harness

-

B1

white 6-pole socket housing

-

at branch cable A15, white 6-pole pin housing of the
on-board monitor wiring harness A

B2

black 6-pole socket housing

-

In vehicles prior to production date 9/98
at branch cable C1, black 6-pole pin housing of the
supplementary wiring harness for navigation C
In vehicles from production date 9/98
at branch cable D1, black 6-pole pin housing of the
supplementary wiring harness for navigation D

B3

white 18-pole socket housing

-

is tied back with cable strap to navigation wiring
harness B

B4

black 6-pole pin housing

-

In vehicles equipped with Basis-Interface Telephone 2
(BIT2), is plugged together with the black 6-pole socket
housing of the Basis-Interface Telephone wiring harness
(BIT2).
In vehicles without Basis-Interface Telephone 2 (BIT2),
insulate and tie back

B5

blue 18-pole socket housing

-

is tied back with cable strap to the navigation wiring
harness B

B6

Bordeaux-coloured 18-pole socket
housing

-

at Bordeaux-coloured 18-pole pin housing at navigation
computer (22)

C

Supplementary wiring harness
for navigation for vehicles prior
to production date 9/98

-

C1

black 6-pole pin housing

-

C2

cable lug Ø 6mm

brown

at ground post X10305 under the rear light, left

C3

cable lug Ø 6mm

brown

at ground post X10012 in the front area of the right sill

C4

1-pole blade terminal contact

C5

1-pole blade terminal contact

white/yellow

black

-

at branch cable B2, black 6-pole socket housing,
of the navigation wiring harness B

at light module X10117 in black 54-pole socket housing,
PIN38
at connector X1171 of ABS control unit in PIN9,
in LHD vehicles tie back excess length
In automatic vehicles with M62 B44 engine and DSC,
from production date 9/97 to production date 9/98
at connector X1171 of ABS control unit in PIN72,
in LHD vehicles tie back excess length.

C6

1-pole blade terminal contact

yellow

at connector X1171 of ABS control unit in PIN42,
in LHD vehicles tie back excess length
In automatic vehicles with M62 B44 engine and DSC,
from production date 9/97 to production date 9/98
at connector X1171 of ABS control unit in PIN73,
in LHD vehicles tie back excess length

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/59

4.

Connection overview

Item

Cable colour

Connection point in vehicle

Supplementary wiring harness
for navigation in vehicles from
production date 9/98

-

-

D1

black 6-pole pin housing

-

D2

1-pole blade terminal contact

white/yellow

at light module X10117 in black 54-pole socket housing,
PIN38

D3

1-pole blade terminal contact

yellow/red

at joint connector X10183 (cable colour at joint connector
yellow/red). If D3 is not required, insulate with shrinkage
tubing and tie back. In LHD vehicles tie back excess
length.

D4

1-pole blade terminal contact

yellow/white

at joint connector X10184 (cable colour at joint connector
yellow/white). If D4 is not required, insulate with
shrinkage tubing and tie back. In LHD vehicles tie back
excess length.

D5

1-pole blade terminal contact

yellow/red

at black 42-pole connector X1170 of hydraulic unit ABS
in PIN35. If D5 not required, insulate with shrinkage
tubing and tie back

D6

1-pole blade terminal contact

yellow/white

at black 42-pole connector X1170 of hydraulic unit ABS
in PIN18. If D6 not required, insulate with shrinkage
tubing and tie back

D

Designation

at branch cable B2, black 6-pole socket housing, of
navigation wiring harness B

-

Antenna extension for
GPS antenna

-

E1

Coaxial pin housing

-

at GPS antenna (6)

E2

Coaxial socket housing

-

at navigation computer (22)

F

Zusatzkabel Tacho A-Signal

-

E

-

F1

schwarzes 1poliges
Buchsengehäuse

black/white

with 2-way insulation-piercing connector at speedo A
signal, cable colour black/white, PIN10 of branch cable
A3, black 17-pole pin housing of the on-board monitor
wiring harness A

F2

1poliger Flachsteckkontakt
KL.TAA

black/white

In vehicles with High instrument cluster (OE555)
pin in at white 18-pole instrument cluster connector
X10113 in PIN 3
In vehicles with Low instrument cluster
insulate with shrinkage tubing and tie back

F3

1poliger Flachsteckkontakt
KL.TAA

white

In vehicles with Low instrument cluster
pin in at white 26-pole instrument cluster connector
X11176 in PIN 14
In vehicles with High instrument cluster (OE555)
insulate with shrinkage tubing and tie back

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/60

5.

Installation and cabling diagram of the on-board monitor wiring harness

A5
A3
A2
A1

A11 A12
A4
A

A9 A8
A7
A6
A13

A15 A16

A14

A10
X13016

F 39 0528 B

The on-board monitor wiring harness A is, as shown, to be installed along the audio or main
wiring harness and to be fastened with cable straps.
When installing the on-board monitor wiring harness A, you should begin at the ground
post X13016 in the area of the C-pillar at rear left.
Branch cable A10, screw on at ground post X13016 in the area of the C-pillar, rear left
Branch cable A4, install to the installation location of the left-hand side TV amplifier at the
C-pillar, left and tie back (is only connected in association with the installation of a video
module and the TV amplifiers)
Branch cable A11 and A12 to the antenna amplifier at the C-pillar, left.
Branch cable A5, install to the installation location of the right TV amplifier at the C-pillar right
and tie back (is only connected in association with the installation of a video module and the
TV amplifiers)
Branch cables A6 to A9 through the opening in the rear window shelf into the boot to the
installation location of the on-board monitor in the side part, rear left
Tie back branch cables A6 to A7 (they are only connected in association with the installation
of a video module and the TV amplifiers)
Branch cables A13 to A16 through the lead-through grommet behind the rear-seat back along
the main cable loom into the boot
Branch cables A13 and A14 to the installation location of the on-board monitor radio in the
side part, rear left
Install branch cable A15 to the installation location of the video module bracket in the side
part, rear left and snap in at mounting clip
Branch cable A16 to the installation location of the navigation computer in the side part, rear
left
The on-board monitor wiring harness A crosses behind the left front seat and from there
is installed along the driveshaft tunnel behind the centre console to the installation location of
the on-board monitor
Branch cables A1 to A3 along the series audio wiring harness to the installation location of
the on-board monitor in the I board.
Any excessive lengths should be tied back
Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/61

6.

Installation and cabling diagram of the supplementary wiring harness for
navigation in vehicles prior to production date 9/98

C4
C

C3
C5
C6
RHD C5
RHD C6

C1

C2

F 39 0530 B

The supplementary wiring harness for navigation C should be installed in vehicles prior to
production date 9/98 as shown and fastened with cable straps.
When installing the supplementary wiring harness for Navigation C, you should begin
with branch cable C1.
Branch cable C1 to installation location of the bracket of the video module, in boot rear left
Branch cable C2 to ground post X10305 under the tail light, left
Branch cables C3 to C6 along the closing panel to the right side part, from there through the
lead-through grommet in the rear window shelf into the interior of the vehicle and from there
along the right main cable loom to the installation location of the light module in the A-pillar,
right
Branch cable C3 to the ground post X10012 in the forward area of the right sill
Branch cables C5 and C6 to the installation location of the ABS control unit, left in the vicinity
of the glove box, or, in RHD vehicles, behind the heater box towards the left to the ABS
control unit on the right in the vicinity of the glove box
Tie back any excess lengths

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/62

7.

Installation and cabling diagram of the supplementary cable for navigation in
vehicles from production date 9/98

D2

D

D5 D6
D3
D4
D1

RHD D3
RHD D4

F 39 0531 B

The supplementary wiring harness for navigation D should be installed in vehicles from
production date 9/98 as shown and fastened with cable straps.
When installing the supplementary wiring harness for Navigation D, you should begin
with branch cable D1.
Branch cable D1 to installation location of the bracket of the video module, in boot rear left
Branch cable D2 to D6 along the closing panel to the right side part, from there through the
lead-through grommet in the rear window shelf into the interior of the vehicle and from there
along the right main cable loom to the installation location of the light module in the A-pillar,
right
Branch cables D3 and D4 to the joint connectors behind the glove box, or, in RHD vehicles,
behind the heater box towards the left to the joint connectors behind the glove box
Branch cables D5 and D6 through the lead-through grommet in the bulkhead into the engine
compartment, right, to the installation location of the hydraulic unit ABS
Tie back any excess lengths

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/63

8.

Install supplementary speedo A signal in vehicles from production date 9/99,
without speedo A signal at radio connector X18126

In vehicles from production date 9/99 you should check to see whether the speedo A
signal is still present at radio connector X18126, PIN10, cable colour black/white in the
instrument panel. If the speedo A signal is not present, the following steps are necessary in
addition.

Only vehicles with High instrument cluster
(OE555)

34
F

8
F1

Illustration shows installation location of the
instrument cluster of a LHD vehicle.You should
proceed in the identical logical sequence for a
RHD vehicle
Decouple and open white 18-pole instrument
cluster connector X10113.

F3
F2
X10113

F 39 0532 B

Pin branch cable F2, 1-pole socket contact,
cable colour black/white of the supplementary
cable speedo A signal F, into the free plug-in
place PIN3 of the connector X10113.
Insulate branch cable F3, 1-pole socket contact,
cable colour white, with shrinkage tubing (8) and
tie back.
Then couple and lock connector X10113.
Install branch cable F1, 1-pole black socket
housing, cable colour black/white, to the radio
connector X18126 in the instrument panel and
fasten with cable straps (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/64

8.

Install supplementary speedo A signal in vehicles from production date 9/99,
without speedo A signal at radio connector X18126
Only vehicles with Low instrument cluster

34
F

Illustration shows installation location of the
instrument cluster of a LHD vehicle.You should
proceed in the identical logical sequence for a
RHD vehicle.

8
F1

F3

F2
X11176

F 39 0533 B

Decouple and open white 26-pole instrument
cluster connector X11176.
Pin branch cable F3, 1-pole socket contact,
cable colour white of the supplementary cable
speedo A signal F, into the free plug-in place
PIN14 of the connector X11176.
Insulate branch cable F2, 1-pole socket contact,
cable colour black/white, with shrinkage tubing
(8) and tie back.
Then couple and lock connector X11176 again.
Install branch cable F1, 1-pole black socket
housing, cable colour black/white, to the radio
connector X18126 in the instrument panel and
fasten with cable straps (34).

Vehicles with High or Low instrument cluster

A
F
X18126

A3

F1

A3
9 F

Cut off excess length of the supplementary
cable speedo A signal F, cable colour
black/white, in the area of branch cable F1.
Then connect free cable end with 2-way
insulation-piercing connector (9) to speedo A
signal, cable colour black/white, PIN10, of
branch cable A3, black 17-pole pin housing,
coming from on-board monitor wiring harness A.

PIN10
F 39 0534 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/65

9.

Install on-board monitor wiring harness, on-board monitor and on-board
monitor radio

Illustration shows C-pillar, left, from inside.

A5
A10

Screw branch cable A10, ring terminal Ø 6mm,
of the on-board monitor wiring harness A, to the
ground post X13016 at the C-pillar, rear left.
Tie back branch cable A4, coaxial pin housing,
of the on-board monitor wiring harness A, with
cable strap (34) (is only connected in association
with the installation of a video module and the TV
amplifiers).

A4

34
X13016

A6-A9

F 39 0535 B

52

51
50
53

54

A11

A12
F 39 0536 B

Install branch cable A5, coaxial pin housing, of
the on-board monitor wiring harness A, on the
rear window shelf along the rear window to the
installation location of the right TV amplifier to the
C-pillar, right, and tie it back with cable straps
(34) (is only connected in association with the
installation of a video module and of the TV
amplifiers).
Install branch cables A6 to A9 through the leadthrough grommet in the rear window shelf into
the boot to the installation location of the onboard monitor radio in the side part, rear left.

Unscrew existing coaxial pin housing (50) from
antenna amplifier (51) and tie back (no longer
required).
Screw branch cable A12, coaxial pin housing,
of on-board monitor wiring harness A, onto the
freed coaxial socket housing (52) of the antenna
amplifier (51).
Unplug existing coaxial socket housing (53) of
antenna amplifier (51) and tie back (no longer
required).
Plug on branch cable A11, coaxial socket
housing, of on-board monitor wiring harness A,
onto the freed coaxial pin housing (54) of the
antenna amplifier (51).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/66

9.

Install on-board monitor wiring harness, on-board monitor and on-board monitor radio

50
51
14
38

A3

F 39 0537 B

Plug together branch cable A3, black 17-pole pin
housing, of the on-board monitor wiring harness
A, with the existing radio connector X18126.
Stick one rattle protector (38) onto the second
rattle protector (38) and then stick it onto the
wiring harness in such a way that the existing
angled coaxial socket housing (50), the black
coaxial socket housing (51) (antenna
connection), the connector of the receiver part
(52) and the plug-in connector A3+X18126 are
enclosed.
The enclosed connections (50, 51, 52), as well as
the enclosed plug-in connector A3+X18126 are
no longer required and should be placed behind
the heating and ventilation operating unit.

A2

Screw on-board monitor holding pin (13) onto
the on-board monitor (12).
Plug branch cable A1, blue 12-pole socket
housing, of the on-board monitor wiring
harness A, onto the blue 12-pole pin housing
(50) at the on-board monitor (12).
Plug branch cable A2, white 12-pole socket
housing, of the on-board monitor wiring
harness A, onto the white pin housing (51) of the
on-board monitor (12).
Then feed the cables into the on-board monitor
cavity (52) and carefully push in the on-board
monitor (12).

52

38
X18126

A2
A1

A

52
51
A1

12
50
13

Before the work steps are carried out as
shown in the illustration, the new function carrier
of the on-board monitor (14) must be equipped
as described in the TIS.

F 39 0538 B

When pushing the on-board monitor in, make
sure that no cables become damaged.

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/67

9.

Install on-board monitor wiring harness, on-board monitor and on-board monitor radio

Screw on-board monitor (12) to the function
carrier of the on-board monitor (14) with four
crossed recessed raised cheese-head screws
M3x8 (15).
Then put the cover for the on-board monitor (16)
onto the on-board monitor (12).

14
INFO
1
2

12

4
5

3

6

FM

AM

MODE

TONE SELECT

MENU

16

15

F 39 0539 B

50

Illustration shows boot, rear left.

28

Insert two plastic expanding nuts 4.8 (28) in the
cross brace (50) in the side part, rear left.
Insert another plastic expanding nut 4.8 (28) in
the frame part, rear left.

28
F 39 0540 B

Place bracket of DSP amplifier (18) in boot at
rear left on the attachment bolt (50) and screw it
on with two hexagon-head self-tapping screws
with washer 4.8x16 (27). Put plug-in nut M5 (26)
on bracket of DSP amplifier (18)

26
18
27

50
F 39 0541 B

Stick sealing strip (36) onto the base carrier (19).
Put five plug-in nuts M5 (25) onto the base
carrier (19) and screw base carrier (19) onto the
boot floor at rear left with two plastic cap nuts
(29) and with one hexagon-head self-tapping
screw with washer 4.8x16 (27).Then insert the
two rubber grommets (30) in the recesses
provided for them in the bracket of the DSP
amplifier (18) and in the base carrier (19).

18
30
36
29

26

19
26

29
27

F 39 0542 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/68

9.

Install on-board monitor wiring harness, on-board monitor and on-board monitor radio

Screw bracket of video module, front, (20) onto
the base carrier (19) with two hexagon-head
bolts with washers M5x14 (25) and onto the
attachment bolt (50) with a plastic cap nut (29).

20
25
29

19
50

F 39 0543 B

24/25
21
30

17

25

19

Insert on-board monitor radio (17) into the
previously fitted rubber grommets (30).
Place bracket of on-board monitor radio and CD
changer (21) in position and screw onto the base
carrier (19) with three hexagon-head screws with
washers M5x14 (25).
Screw on-board monitor radio (17) to the bracket
for on-board monitor radio and CD changer (21)
with hex nut with washer M5 (24) or with
hexagon-head bolt with washer M5x14 (25),
depending on the design of the on-board
monitor radio.

F 39 0544 B

Remove blue locking clip (5) from branch cable
A13, black 17-pole socket housing, of the onboard monitor wiring harness A and insert
branch cable A14, 10-pole socket housing, of the
on-board monitor wiring harness A into branch
cable A13.

A14
A13

In vehicles with CD changer but without DSP
amplifier, the control cable of the on-board
monitor radio/CD changer has to be fitted in
addition.

50

F 39 0545 B

Secure branch cable A14 with blue locking clip
(50).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/69

9.

Install on-board monitor wiring harness, on-board monitor and on-board monitor radio

A6

A7

34
A13
A9

35

17

50
A8

A15
10

21

F 39 0546 B

Connect branch cable A8, black coaxial socket
housing (antenna connection), coming from onboard monitor wiring harness A, to on-board
monitor radio (17).
Connect branch cable A9, angled coaxial socket
housing, coming from on-board monitor wiring
harness A, to on-board monitor radio (17).
Connect branch cable A13, black 17-pole socket
housing, coming from on-board monitor wiring
harness A, to on-board monitor radio (17).
Insert cable holder (35) in the bore hole (50) in
the bracket of the on-board monitor radio and
CD-changer (21).
The cables of the connected branch cables A8
and A9 and if necessary also the control cable of
the on-board monitor radio /CD changer should
be fastened with the cable holder (35).
Clip branch cable A15, tan-coloured 6-pole pin
housing, coming from on-board monitor wiring
harness A, into the mounting clip (10) (will be
latched later to the bracket of the video module,
front).
Tie back branch cables A6 and A7, angled
coaxial socket housings, coming from on-board
monitor wiring harness A, to on-board monitor
wiring harness A with cable strap (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/70

10. Install supplementary wiring harness for navigation in vehicles prior to
production date 9/98

C1
A
C

10
A15

C2
20

34

X10305
F 39 0547 B

Clip the mounting clip (10) with the engaged
branch cable A15 coming from on-board monitor
wiring harness A into the bracket of the video
module, front (20).
Engage branch cable C1, black 6-pole pin
housing, coming from supplementary wiring
harness for navigation C, onto branch cable A15.
Screw branch cable C2, cable lug Ø 6 mm, onto
ground post X10305 under the left tail light.
Install supplementary wiring harness for
navigation C along the closing panel to the right
side part and from there through the leadthrough grommet in the boot upper right and
fasten with cable straps (34).
Install supplementary wiring harness for
navigation C with branch cables C3, C4, C5 and
C6 through the lead-through grommet (50) in the
vehicle interior and along the right-hand side
main cable loom to the installation location of the
light module in the A-pillar, right. Fasten with
cable straps (34).

C

50
34

F 39 0548 B

Screw branch cable C3, cable lug Ø 6 mm, to
ground post X10012 in the front area of the right
sill.

C

C3

X10012

F 39 0549 B

Dismantle light module (50), unplug the black
54-pole socket housing X10017 from the light
module (50) and open it.
Plug branch cable C4, 1-pole blade terminal
contact, cable colour white/yellow, into PIN38 of
the black 54-pole socket housing X10117.Then
close black socket housing X10117, connect it
and re-install light module (50).
If necessary tie back excess length of
supplementary wiring harness for navigation C
before branch cable C4.

C4
X10117

50
F 39 0550 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/71

10. Install supplementary wiring harness for navigation in vehicles prior to production
date 9/98

Illustration shows installation in a left-hand
drive vehicle.The identical logical procedure
should be followed for right-hand drive
vehicles.

C5
C6
X1171

51

34

50
F 39 0551 B

In left-hand drive vehicles, install branch cable
C5 and C6 coming from supplementary wiring
harness for navigation C, to the ABS control unit
(5) on the left in the vicinity of the glove box
(excess length must be tied back).
In right-hand drive vehicles, install branch cables
C5 and C6 coming from supplementary wiring
harness for navigation C, behind the heater box
towards the left to the ABS control unit on the
right in the vicinity of the glove box. Dismantle
ABS control unit (50). Unpin control unit
connector X1171 and take it apart. Insert branch
cables C5 and C6 in the plug lead-in (51).
Plug branch cable C5, 1-pole blade terminal
contact, cable colour black, into PIN9 of the
control unit connector X1171. If PIN9 is already
assigned, the contact part of branch cable C5
must be cut off and the black cable in the space
of the ABS connector must be soldered to the
cable of PIN9 and insulated.
Insert branch cable C6, 1-pole blade terminal
contact, cable colour yellow, in PIN 42 of the
control unit connector X1171. If PIN42 is already
assigned, the contact part of branch cable C6
must be cut off and the yellow cable in the
space of the ABS connector must be soldered to
the cable of PIN42 and insulated.
Re-assemble control unit connector X1171 and
plug it onto ABS control unit (50). Install ABS
control unit (50) and fasten supplementary wiring
harness for navigation C with cable straps (34).
Only for automatic vehicles with M62 B44
engine and DSC, from production date 9/97 to
production date 9/98
Insert branch cable C5, 1-pole blade terminal
contact, cable colour black, in PIN 72 of the
control unit connector X1171. If PIN72 is already
assigned, the contact part of branch cable C5
must be cut off and the black cable in the space
of the ABS connector must be soldered to the
cable of PIN72 and insulated.
Insert branch cable C6, 1-pole blade terminal
contact, cable colour yellow, in PIN 73 of the
control unit connector X1171. If PIN73 is already
assigned, the contact part of branch cable C6
must be cut off and the yellow cable in the
space of the ABS connector must be soldered to
the cable of PIN73 and insulated.
Re-assemble control unit connector X1171 and
plug it onto ABS control unit (50). Install ABS
control unit (50) and fasten supplementary wiring
harness for navigation C with cable straps (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/72

11. Choose installation of the supplementary wiring harness for navigation in
vehicles from production date 9/98
Illustration shows engine compartment, front
right.

50

PIN35
PIN18

X1170
F 39 0552 B

Unplug the black 42-pole connector X1170 of the
hydraulic unit ABS (50) in the engine
compartment, front right. Open it and check
whether PIN18 and PIN35 are assigned.
If PIN18 and PIN35 are not assigned, installation
of the supplementary wiring harness for
navigation should be carried out as described in
Chapter 12.
Chapter 12. Install supplementary wiring harness
for navigation in vehicles from production date
9/98 (PIN18 and PIN35 at connector of the ABS
hydraulic unit not assigned).
If PIN18 and PIN35 are assigned, installation of
the supplementary wiring harness for navigation
should be carried out as described in
Chapter 13.
Chapter 13.Install supplementary wiring harness
for navigation in vehicles from production date
9/98 (PIN18 and PIN35 at connector of the ABS
hydraulic unit assigned)
If PIN18 is assigned and PIN35 not assigned,
installation of the supplementary wiring harness
for navigation should be carried out as described
in Chapter 14.
Chapter 14. Install supplementary wiring harness
for navigation in vehicles from production date
9/98 (PIN18 assigned and PIN35 not assigned at
connector of the ABS hydraulic unit).
If PIN18 is not assigned and PIN35 assigned,
installation of the supplementary wiring harness
for navigation should be carried out as described
in Chapter 15.
Chapter 15. Install supplementary wiring harness
for navigation in vehicles from production date
9/98 (PIN18 not assigned and PIN35 assigned at
connector of the ABS hydraulic unit)

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/73

12. Install supplementary wiring harness for navigation in vehicles from
production date 9/98 (PIN18 and PIN35 at connector of the hydraulic unit
ABS not assigned)

D1
A
D

10
A15

20

34

F 39 0553 B

Illustration shows boot, rear left.
Clip the mounting clip (10) with the engaged
branch cable A15 coming from on-board monitor
wiring harness A into the bracket of the video
module, front (20).
Engage branch cable D1, black 6-pole pin
housing, coming from supplementary wiring
harness for navigation D, onto branch cable A15.
Install supplementary wiring harness for
navigation D along the closing panel to the right
side part and from there through the leadthrough grommet in the boot upper right. Attach
supplementary wiring harness for navigation D
with cable straps (34).
Install supplementary wiring harness for
navigation D with branch cables D2, D3, D4, D5
and D6 through the lead-through grommet (50)
in the vehicle interior and along the right-hand
side main cable loom to the installation location
of the light module in the A-pillar, right. Fasten
with cable straps (34).

D

50

34
F 39 0554 B

Dismantle light module (50), unplug the black
54-pole socket housing X10017 from the light
module (50) and open it.
Plug branch cable D2, 1-pole blade terminal
contact, cable colour white/yellow, into PIN38 of
the black 54-pole socket housing X10117.Then
close black socket housing X10117, connect it
and re-install light module (50).
If necessary tie back excess length of
supplementary wiring harness for navigation D
before branch cable D2.

D2
X10117

50
F 39 0555 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/74

12. Install supplementary wiring harness for navigation in vehicles from production date 9/98
(PIN18 and PIN35 at connector of the hydraulic unit ABS not assigned)

D

D3
D4

D5 D6

F 39 0556 B

50

37

D3 C4
D
34

F 39 0557 B

Before further installation of the
supplementary wiring harness for navigation
D is undertaken, the cover of the control unit
box in the engine compartment, right, should
be dismounted.
Insulate branch cables D3 and D4 of the
supplementary wiring harness for navigation D
with shrinkage tubing and tie back in the area of
the right front sill.
Install branch cables D5 and D6 of the
supplementary wiring harness for navigation D
through the lead-through grommet in the
bulkhead, front right, into the control unit box
and from there onwards to the hydraulic unit
ABS and connect them to connector X1170 of
the hydraulic unit ABS.

Illustration shows the area behind the glove
box in a left-hand drive vehicle.You should
proceed in the identical sequence for right-hand
drive vehicles.
Feed the supplementary wiring harness for
navigation D with branch cables D5 and D6
through the lead-through grommet (50) in the
bulkhead, front right, to the control unit box in
the engine compartment and fasten with cable
straps (34).
Push on a shrinkage tubing (37) for insulation in
each case onto branch cable D3, 1-pole blade
terminal contact, cable colour yellow/red and
branch cable D4, 1-pole blade terminal contact,
cable colour yellow/white, of the supplementary
wiring harness for navigation D, and shrink them
on with hot-air dryer.
Then tie back branch cables D3 and D4 in the
area of the right front sill with cable straps (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/75

12. Install supplementary wiring harness for navigation in vehicles from production date 9/98
(PIN18 and PIN35 at connector of the hydraulic unit ABS not assigned)

34

BMW
PIN18
X1170
PIN35

51

50 D

D5

Carefully cut open rubber grommet (50) at the
control unit box in the front area and push
supplementary wiring harness for navigation D
with branch cables D5 and D6 carefully through
the opening in the rubber grommet (50) and
install to the hydraulic unit ABS (51).
Having installed the supplementary wiring
harness for navigation D, seal the rubber
grommet (50) with silicon (splash-water
protection).

D6
F 39 0558 B

Decouple the black 42-pole connector X1170 of
the hydraulic unit ABS and connect branch
cables D5 and D6 as follows:
Pin in branch cable D5, 1-pole blade terminal
contact, cable colour yellow/red, into connector
X1170 of the hydraulic unit ABS in plug-in place
PIN35.
Pin in branch cable D6, 1-pole blade terminal
contact, cable colour yellow/white, into connector
X1170 of the hydraulic unit ABS in plug-in place
PIN18.
Re-couple connector X1170 and plug onto
hydraulic unit ABS.
Then fasten supplementary wiring harness for
navigation D in the area of the engine
compartment with cable straps (26).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/76

13. Install supplementary wiring harness for navigation in vehicles from
production date 9/98 (PIN18 and PIN35 at connector of the hydraulic unit
ABS assigned)

D1
A
D

10
A15

20

34

F 39 0553 B

Illustration shows boot, rear left.
Clip the mounting clip (10) with the engaged
branch cable A15 coming from on-board monitor
wiring harness A into the bracket of the video
module, front (20).
Engage branch cable D1, black 6-pole pin
housing, coming from supplementary wiring
harness for navigation D, onto branch cable A15.
Install supplementary wiring harness for
navigation D along the closing panel to the right
side part and from there through the leadthrough grommet in the boot upper right. Attach
supplementary wiring harness for navigation D
with cable straps (34).
Install supplementary wiring harness for
navigation D with branch cables D2, D3, D4, D5
and D6 through the lead-through grommet (50)
in the vehicle interior and along the right-hand
side main cable loom to the installation location
of the light module in the A-pillar, right. Fasten
with cable straps (34).

D

50

34
F 39 0554 B

Dismantle light module (50), unplug the black
54-pole socket housing X10017 from the light
module (50) and open it.
Plug branch cable D2, 1-pole blade terminal
contact, cable colour white/yellow, into PIN38 of
the black 54-pole socket housing X10117.Then
close black socket housing X10117, connect it
and re-install light module (50).
If necessary tie back excess length of
supplementary wiring harness for navigation D
before branch cable D2.

D2
X10117

50
F 39 0555 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/77

13. Install supplementary wiring harness for navigation in vehicles from production date 9/98
(PIN18 and PIN35 at connector of the hydraulic unit ABS assigned)

D
D5
D6
D3
D4
RHD D3
RHD D4
F 39 0562 B

50

37

D3
D4

D5
D6
34

Insulate branch cables D5 and D6 of the
supplementary wiring harness for navigation D
with shrinkage tubing and tie back in the area of
the right front sill.
In left-hand drive vehicles, install branch cables
D3 and D4 of the supplementary wiring harness
for navigation D to the joint connector box
behind the glove box (excess length must be tied
back) and connect to the joint connectors
X10183 and X10184.
In right-hand drive vehicles, install branch cables
D3 and D4 of the supplementary wiring harness
for navigation D behind the heater box to the left
to the joint connector box behind the glove box
and connect to the joint connectors X10183 and
X10184.

Illustration shows the area behind the glove
box in a left-hand drive vehicle.You should
proceed in the identical sequence for right-hand
drive vehicles.

D

Push on a shrinkage tubing (37) for insulation in
each case onto branch cable D5, 1-pole blade
terminal contact, cable colour yellow/red, and
branch cable D6, 1-pole blade terminal contact,
cable colour yellow/white, of the supplementary
wiring harness for navigation D, and shrink them
on with hot-air dryer.

F 39 0563 B

Then tie back branch cables D5 and D6 in the
area of the right front sill with cable straps (34).
Plug branch cable D3, 1-pole blade terminal
contact, cable colour yellow/red, onto the joint
connector X10183 (cable colour at joint
connector yellow/red) in the joint connector box
(50) behind the glove box.
Plug branch cable D4, 1-pole blade terminal
contact, cable colour yellow/white, onto the joint
connector X10184 (cable colour at joint
connector yellow/white) in the joint connector
box (50) behind the glove box.
Any excessive lengths of branch cables D3 and
D4 should be tied back with cable straps (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/78

14. Install supplementary wiring harness for navigation in vehicles from
production date 9/98 (PIN18 assigned and PIN35 not assigned at connector
of the hydraulic unit ABS)

D1
A
D

10
A15

20

34

F 39 0553 B

Illustration shows boot, rear left.
Clip the mounting clip (10) with the engaged
branch cable A15 coming from on-board monitor
wiring harness A into the bracket of the video
module, front (20).
Engage branch cable D1, black 6-pole pin
housing, coming from supplementary wiring
harness for navigation D, onto branch cable A15.
Install supplementary wiring harness for
navigation D along the closing panel to the right
side part and from there through the leadthrough grommet in the boot upper right. Attach
supplementary wiring harness for navigation D
with cable straps (34).
Install supplementary wiring harness for
navigation D with branch cables D2, D3, D4, D5
and D6 through the lead-through grommet (50)
in the vehicle interior and along the right-hand
side main cable loom to the installation location
of the light module in the A-pillar, right. Fasten
with cable straps (34).

D

50

34
F 39 0554 B

Dismantle light module (50), unplug the black
54-pole socket housing X10017 from the light
module (50) and open it.
Plug branch cable D2, 1-pole blade terminal
contact, cable colour white/yellow, into PIN38 of
the black 54-pole socket housing X10117.Then
close black socket housing X10117, connect it
and re-install light module (50).
If necessary tie back excess length of
supplementary wiring harness for navigation D
before branch cable D2.

D2
X10117

50
F 39 0555 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/79

14. Install supplementary wiring harness for navigation in vehicles from production date 9/98
(PIN18 assigned and PIN35 not assigned at connector of the hydraulic unit ABS)

D
D5 D6

D3
D4
RHD D3
RHD D4
F 39 0567 B

50
51

37

D3 D4
D
34

F 39 0568 B

Before further installation of the
supplementary wiring harness for navigation D is
undertaken, the cover for the control unit box in
the engine compartment, right, should be
dismounted.
Install branch cables D5 and D6 of the
supplementary wiring harness for navigation D
through the lead-through grommet in the
bulkhead, front right, into the control unit box
and from there onwards to the hydraulic unit
ABS.
Only connect branch cable D5 to the connector
X1170 of the hydraulic unit ABS.
Insulate branch cable D6 with shrinkage tubing
and tie it back.
In left-hand drive vehicles, install branch cable
D3 and D4 of the supplementary wiring harness
for navigation D to the joint connector box
behind the glove box (excess length must be tied
back).
In right-hand drive vehicles, install branch cable
D3 and D4 behind the heater box towards the
left to the joint connector box behind the glove
box and fasten with cable straps.
Insulate branch cable D3 with shrinkage tubing
and tie back.
Only connect branch cable D4 to the joint
connector X10184.
Illustration shows the area behind the glove
box in a left-hand drive vehicle.You should
proceed in the identical sequence for right-hand
drive vehicles.
Feed the supplementary wiring harness for
navigation D with branch cables D5 and D6
through the lead-through grommet (50) in the
bulkhead, front right, to the control unit box in
the engine compartment and fasten with cable
straps (34).
Push on a shrinkage tubing (37) for insulation
onto branch cable D3, 1-pole blade terminal
contact, cable colour yellow/red, shrink it on with
hot-air dryer and tie it back.
Then connect branch cable D4, 1-pole blade
terminal contact, cable colour yellow/white to
joint connector X10184, (cable colour at joint
connector yellow/white) in the joint connector
box (51) behind the glove box.
Any excess length of branch cable D3 and D4
should be tied back with cable strap (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/80

14. Install supplementary wiring harness for navigation in vehicles from production date 9/98
(PIN18 assigned and PIN35 not assigned at connector of the hydraulic unit ABS)

34

37

BMW

X1170

PIN35
51

50 D

D5
D6
F 39 0569 B

Carefully cut open rubber grommet (50) at the
control unit box in the front area and push
supplementary wiring harness for navigation D
with branch cables D5 and D6 carefully through
the opening in the rubber grommet (50) and
install to the hydraulic unit ABS (51).
Having installed the supplementary wiring
harness for navigation D, seal the opening in the
rubber grommet (50) with silicon (splash-water
protection)
Decouple the black 42-pole connector X1170 of
the hydraulic unit ABS and connect branch cable
D5 as follows:
Pin in branch cable D5, 1-pole blade terminal
contact, cable colour yellow/red, into connector
X1170 of the hydraulic unit ABS in plug-in place
PIN35.
Push onto branch cable D6, 1-pole blade
terminal contact, cable colour yellow/white, one
shrinkage tubing (37) for insulation, shrink on
with hot air blower and tie back.
Re-couple connector X1170 and plug onto
hydraulic unit ABS.
Then fasten supplementary wiring harness for
navigation D in the area of the engine
compartment with cable straps (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/81

15. Install supplementary wiring harness for navigation in vehicles from
production date 9/98 (PIN18 not assigned and PIN35 assigned at connector
of the hydraulic unit ABS)

D1
A
D

10
A15

20

34

F 39 0553 B

Illustration shows boot, rear left.
Clip the mounting clip (10) with the engaged
branch cable A15 coming from on-board monitor
wiring harness A into the bracket of the video
module, front (20).
Engage branch cable D1, black 6-pole pin
housing, coming from supplementary wiring
harness for navigation D, onto branch cable A15.
Install supplementary wiring harness for
navigation D along the closing panel to the right
side part and from there through the leadthrough grommet in the boot upper right. Attach
supplementary wiring harness for navigation D
with cable straps (34).

Install supplementary wiring harness for
navigation D with branch cables D2, D3, D4, D5
and D6 through the lead-through grommet (50)
in the vehicle interior and along the right-hand
side main cable loom to the installation location
of the light module in the A-pillar, right. Fasten
with cable straps (34).

D

50

34
F 39 0554 B

Dismantle light module (50), unplug the black
54-pole socket housing X10017 from the light
module (50) and open it.
Plug branch cable D2, 1-pole blade terminal
contact, cable colour white/yellow, into PIN38 of
the black 54-pole socket housing X10117.Then
close black socket housing X10117, connect it
and re-install light module (50).
If necessary tie back excess length of
supplementary wiring harness for navigation D
before branch cable D2.

D2
X10117

50
F 39 0555 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/82

15. Install supplementary wiring harness for navigation in vehicles from production date 9/98
(PIN18 not assigned and PIN35 assigned at connector of the hydraulic unit ABS)

D

D5 D6
D4
D3
RHD D4
RHD D3
F 39 0573 B

50
51

37

D3 D4
D
34

F 39 0574 B

Before further installation of the
supplementary wiring harness for navigation
D is undertaken, the cover of the control unit
box in the engine compartment, right, should
be dismounted.
Install branch cables D5 and D6 of the
supplementary wiring harness for navigation D
through the lead-through grommet in the
bulkhead, front right, into the control unit box
and from there onwards to the hydraulic unit
ABS.
Insulate branch cable D5 with shrinkage tubing
and tie it back.
Connect only branch cable D6 to connector
X1170 of hydraulic unit ABS.
In left-hand drive vehicles, install branch cables
D3 and D4 of the supplementary wiring harness
for navigation D to the joint connector box
behind the glove box (excess lengths must be
tied back).
In right-hand drive vehicles, install branch cables
D3 and D4 behind the heater box towards the
left to the joint connector box behind the glove
box and fasten with cable straps. Only connect
branch cable D3 to joint connector X10183.
Insulate branch cable D4 and tie it back.

Illustration shows the area behind the glove
box in a left-hand drive vehicle.You should
proceed in the identical sequence for right-hand
drive vehicles.
Feed the supplementary wiring harness for
navigation D with branch cables D5 and D6
through the lead-through grommet (50) in the
bulkhead, front right, to the control unit box in
the engine compartment and fasten with cable
straps (34).
Push a shrinkage tubing (37) for insulation onto
branch cable D4, 1-pole blade terminal contact,
cable colour yellow/white, shrink it on with hot-air
dryer and tie it back.
Then connect branch cable D3, 1-pole blade
terminal contact, cable colour yellow/red, to joint
connector X10183 (cable colour at joint
connector yellow/red) in the joint connector box
(51) behind the glove box.
Any excess length of branch cable D3 and D4
should be tied back with cable straps (34)

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/83

15. Install supplementary wiring harness for navigation in vehicles from production date 9/98
(PIN18 not assigned and PIN35 assigned at connector of the hydraulic unit ABS)

34

BMW
PIN18

37
X1170

51

50 D

D5
D6
F 39 0575 B

Carefully cut open rubber grommet (50) at the
control unit box in the front area and push
supplementary wiring harness for navigation D
with branch cables D5 and D6 carefully through
the opening in the rubber grommet (50) and
install to the hydraulic unit ABS (51).
Having installed the supplementary wiring
harness for navigation D, seal the opening in the
rubber grommet (50) with silicon (splash-water
protection).
Decouple the black 42-pole connector X1170 of
the hydraulic unit ABS and connect branch cable
D6 as follows:
Pin branch cable D6, 1-pole blade terminal
contact, cable colour yellow/white, into connector
X1170 of the hydraulic unit ABS in plug-in place
PIN18.
Push onto branch cable D5, 1-pole blade
terminal contact, cable colour yellow/red, one
shrinkage tubing (37) for insulation, shrink on
with hot air blower and tie back.
Re-couple connector X1170 and plug onto
hydraulic unit ABS.
Then fasten supplementary wiring harness for
navigation D in the area of the engine
compartment with cable straps (34).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/84

16. Install navigation system

Overview for installation of the navigation wiring
harness B and the antenna extension for GPS
antenna E.

E1

B1

B5

B3

E

B6
B4
E2
B2

B
F 39 0576 B

Navigation wiring harness B
Branch cable B1 to free branch cable A15
coming from on-board monitor wiring harness A
at bracket of video module, front
Branch cable B2 to free branch cable C1/D1 of
the supplementary wiring harness for navigation
C/D at the bracket of the video module, front
Tie back branch cable B3 at navigation wiring
harness B.
Branch cable B4 to connector of Basis-Interface
Telephone 2 (BIT2) or tie back in vehicles without
(BIT2)
Branch cables B5 and B6 to installation location
of the navigation computer
Antenna extension for GPS antenna E
Branch cable E1 to installation location of the
GPS antenna under the rear window shelf
Branch cable E2 to installation location of the
navigation computer.

Place support of GPS antenna (11) on the GPS
antenna (6) and attach it with 2 expanding rivets
(32)

32

11
6
F 39 0577 B

Illustration shows rear window shelf, left.
Take out pre-punched cut-out (50) under the rear
window shelf.
Check existing attachment points (51) for
diameter Ø 8 mm. If necessary, rebore
attachment points to diameter Ø 8 mm. Press in
attachment grommets (31) into the attachment
points (51).

31
50

51

F 39 0578 B
Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/85

16. Install navigation system

34

6

50
E
E1

31

Insert holder for GPS antenna with mounted GPS
antenna in the attachment grommets (31).
Connect together branch cable E1, coaxial pin
housing, of the antenna extension for GPS
antenna E, with the antenna cable (50) of the
GPS antenna (6).
Install antenna extension for GPS antenna E
along the audio wiring harness, through the
lead-through grommet behind the rear seat back
to the installation location of the navigation
computer in the boot, rear left and fasten with
cable straps (34).

F 39 0579 B

Put plug-in nut M5 (26) onto bracket for video
module, front (20).
Insert bracket of navigation computer (23), screw
on with the hex nut with washer M5 (24) to the
threaded bolt (50) of the reinforcement of the
water gutter and with two hexagon-head bolts
with washers M5x14 (25) to the bracket of the
DSP amplifier (18) and to the bracket of the video
module, front (20).

50
23

24

26

18
20

25

If the vehicle is equipped with telephone or
handy, the existing hex nut with washer M5 of the
bracket of the telephone should be used.

F 39 0580 B

B5

23
34

B6
E2
A16

34

F 39 0581 B

Push branch cable A16, blue 18-pole socket
housing, of the on-board monitor wiring
harness A through the bracket of the navigation
computer (23).
Push branch cable B5, blue 18-pole socket
housing, and branch cable B6, Bordeauxcoloured 18-pole socket housing, of the
navigation wiring harness B, through the bracket
of the navigation computer (23).
Then tie back branch cable B5 with cable strap
(34) to the navigation wiring harness B.
Push branch cable E2, coaxial socket housing, of
the antenna extension for GPS antenna E
through the bracket of the navigation computer
(23).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/86

16. Install navigation system

34

C/D

C1/D1

A

A15
B

B3
34
B1

B4
B2
F 39 0582 B

Tie back branch cable B3, white 18-pole socket
housing of the navigation wiring harness B with
cable strap (34) to the navigation wiring
harness B.
Plug together branch cable B2, black 6-pole
socket housing, of the navigation wiring harness
B with the branch cable C1/D1, black 6-pole pin
housing, coming from supplementary wiring
harness for navigation C/D.
Plug together branch cable B1, white 6-pole
socket housing, of the navigation wiring
harness B with branch cable A15, white 6-pole
pin housing, of the on-board monitor wiring
harness A.
Then fasten navigation wiring harness B,
on-board monitor wiring harness A and
supplementary wiring harness for navigation C/D
with cable straps (34).
In vehicles which are equipped with Basis
Interface Telephone 2 (BIT 2), branch cable B4,
black 6-pole pin housing, of the navigation wiring
harness B should be plugged together with the
black 6-pole socket housing of the Basis
Interface Telephone 2 wiring harness (BIT2).
In vehicles without Basis Interface Telephone 2
(BIT2), insulate branch cable B4 and tie back.

B
A

Plug in branch cable A16, blue 18-pole socket
housing, of the on-board monitor wiring
harness A, to the navigation computer (22).
Plug in branch cable B6, Bordeaux-coloured
18-pole socket housing with tied-back branch
cable B5 of the navigation wiring harness B, to
the navigation computer (22).
Plug in branch cable E2, coaxial socket housing,
of the antenna extension for GPS antenna E to
the navigation computer (22).

E

23

A16
B6
E2
22
F 39 0583 B

When pushing in the navigation computer
(22), care should be taken to see that no cables
or leads get jammed in or damaged (also behind
the navigation computer).
Push navigation computer (22) into the bracket of
the navigation computer (23) until it engages.
Then install the new trim panel of the boot, rear
left, which has been separately ordered in
accordance with the Electronic Parts Catalogue
(EPC).

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/87

17. Coding and finalising operations
If the video module and TV amplifiers forTV function are to be fitted additionally in the
vehicle, the Coding and Finalising operations should be carried out after the video module
and TV amplifiers forTV function have been fitted.

Coding
This system is coding-relevant.
So that the retrofit system:
– is fully functional and
– in association with the other electrical vehicle systems excludes malfunctions and faults,
a coding of this retrofit system, and if necessary other vehicle components, must be carried
out and stored in the central coding key of the IKE.
This coding is carried out automatically with the respective current coding programme in the
"Retrofit" path.
The sequence is operator-guided and you should note the relevant text instructions when
carrying out the individual steps.

Procedure:








Connect DIS/MoDIC to the vehicle
Ignition "ON"
Selection "Coding ZCS"
Confirm input data with "Y" (only with MoDIC)
Series: "E39"
Path: "2 Retrofit"
System: "7 Navigation"

A "Navigation CD-ROM Operating software V16" is necessary for loading the operating
system.
Caution! Do not put the CD-ROM "Operating software V16" in the CD drive yet! Put the
CD-ROM "Operating software V16" in only when told to do so on the on-board monitor.
The language coding is carried out simultaneously with this CD-ROM "Operating software
V16".








Start automatic coding (confirm with "Y")
Follow the instructions on the on-board monitor
Print out new master label of the changed coding key and stick it in the vehicle boot on
the right in the area of the battery
After the message "Coding ended" on the screen of the DIS/MoDIC, ignition "OFF",
wait for at least 10 seconds and then ignition "ON" again.
Print out error memory
Insert CD-ROM "Road map" in the navigation computer
Carry out function test.

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/88

17. Coding and finalising operations

In vehicles with DSP amplifier, the DSP amplifier must be newly coded in addition.

Procedure:












Connect DIS/MoDIC to the vehicle
Ignition "ON"
Selection "Coding ZCS"
Confirm input data with "Y" (only with MoDIC)
Series: "E39"
Path: "1 Recoding"
System: "82 DSP "
Start automatic coding (confirm with "Y")
After the message "Coding ended" on the screen of the DIS/MoDIC, ignition "OFF",
wait for at least 10 seconds and then ignition "ON" again.
Print out error memory
Carry out function test.

Language coding
The language coding can be carried out again via the "Navigation CD-ROM Operating
software V16".

Finalising operations
Connect battery
Carry out function test
Print out error memory
Reassemble the vehicle in the reverse order of disassembly.

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/89

18. Connection description forTV function

This chapter should only be taken note of if the vehicle is to be additionally equipped with
TV function.
To be in a position to equip the vehicle with TV function, the necessary parts (video module,
TV amplifiers, small parts) have to be ordered separately with reference to the Electronic Parts
Catalogue (EPC) and fitted.
The relevant branch cables of the wiring harnesses have also to be connected as follows:
Undo the tied-back branch cable A4, coaxial pin housing, of the on-board monitor wiring
harness A, and plug it onto the previously mounted left TV amplifier in the left C-pillar.
Undo the tied-back branch cable A5, coaxial pin housing, of the on-board monitor wiring
harness A, and plug it onto the previously mounted right TV amplifier in the right C-pillar.
Unplug branch cable A16, blue 18-pole socket housing of the on-board monitor wiring
harness A from the navigation computer.
Undo branch cable B5, blue 18-pole socket housing, tied back to navigation wiring
harness B, and plug it into the blue 18-pole pin housing at the navigation computer.
Undo branch cable A6, angled coaxial socket housing, and A7, angled coaxial socket housing
(both tied back to the on-board monitor wiring harness A), and undo branch cable B3, white
18-pole socket housing, tied back to navigation wiring harness B.
Then install branch cables A6, A7, A16 and B3 to the video module and plug into the video
module as follows:
Plug in branch cable A6 and A7, angled coaxial socket housing, at the two coaxial pin
housings of the video module.
Plug in branch cable A16, blue 18-pole socket housing, at blue 18-pole pin housing of the
video module.
Plug in branch cable B3, white 18-pole socket housing, at the white 18-pole pin housing of
the video module.
Should the vehicle be equipped at a later date with TV function, the system must be newly
coded. For coding see Chapter 17 "Coding and finalising operations".

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/90

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

12

3

11

2

8

1

Date: 10.2000

N9

14

6

12

3

11

2

8

1

16

ANT

1393903.9
LTG VERDRILLT

RADRH- RADRH+ RADLH- RADLH+ RADRV- RADRV+ RADLV- RADLV+

1393904.9
LTG VERDRILLT

0,5
WS

1393905.9
LTG VERDRILLT

ANT

16

0,75 0,75
0,75 0,75 0,75 0,75 0,75 0,75
BROR BLSW BROR GESW BROR BLRT BROR GERT

1393906.9
LTG VERDRILLT

RADRH- RADRH+ RADLH- RADLH+ RADRV- RADRV+ RADLV- RADLV+

6

4

7

I-BUS

TELM

TAA

10

0,35
0,35
WSBR WSGRGE

0,35
SWWS

9

30<64

2,5
RTGN

RADIO RADIO RADIO
/HIFI
/HIFI
/HIFI

RADIO
/HIFI

RADIO
/HIFI

R

5

1,5
VIWS

-

13

58G

0,5
GRRT

-

VB 58G

0,5
RTGN
30<64

2

0,5
RTGN
30<64

1

RADIO/HIFI

X18126

A197

-

-

X1362

VB 30 RADIO VB R

VB I-BUS

X229

X1543

X18344

0,5
GRRT

1,5
VIWS

-

58G

VB TACHO A

R

13

X581

30<64

5

2,5
RTGN

I-BUS

9

0,35
WSGRGE

TELM

TAA

7

0,35
SWWS

4

10

VIDEOMODUL

14

RADIO/HIFI

X6500S

BORDMONITOR
I/K-BUS

0,5
WSGRGE

3

0,35
SW

4
VMG31

5
0,35
SW

VMB

16

7

14

11

VMG31

5

0,5
BR

RADIO/HIFI

MASSE STEREO/HIFI
-

X13016

0,5
BR

6

VMB

0,35
SCHIRM

VMG

31E
10

VMR31

VMR

0,35
SCHIRM

7
0,5
BRRT

VM+

9

15

VMB31

VM-

18

12

VMLC31

10

VM+

5

VM-

0,5
0,5
GERT GEBR

RADIO/HIFI

X18804

X18804

X18802

12

11

R
VMLC31 PL

0,35
SCHIRM

VMB31

6

7

30<64

1386696.9
LTG VERDRILLT

1724213.9
1724213.9
1724213.9
LTG1-ADR.GESCH. LTG1-ADR.GESCH. LTG1-ADR.GESCH.

0,35
SW

3
VMG

2
VMR31

1
VMR

A196

6

10

9

6

7

1

X18126
15

2,5
BR

31E
RADIO/HIFI

X18805
2

TAPER+ TAPER-

1386698.9
LTG VERDRILLT

TAPEL+ TAPEL-

1386699.9
LTG VERDRILLT

0,5
0,5
0,5
0,5
BLSW BLBR GESW GEBR

TAPER+ TAPER-

0,5
SW

4

TAPEL+ TAPEL-

3

RADIO/HIFI

X18801

PL

12

1

58G

I/K-BUS
RADIO/HIFI

X18802

30<64

8

RADIO/HIFI
0,5
VIWS

0,5
GRRT

0,5
RTGN

0,5
WSGRGE

58G

VB 58G

X1362

0,5
RTGN

VB I-BUS
-

X18344

RADIO/HIFI

-

VB R

RADIO/HIFI

RADIO/HIFI

-

VB 30 RADIO

X1543

X229

2

X18344

RADIO/HIFI

MASSE STEREO/HIFI
-

4

TAA

5

R 30<64

1

0,35
SWWS

0,5
VIWS

1,5
RTGN

3

RADIO/HIFI

X1532S

2

31E
0,75
BR

RADIO
/HIFI

MASSE
STEREO/HIFI

X13016

F 39 0584 B

I/K-BUS

0,5
WSGRGE

RADIO RADIO RADIO RADIO
/HIFI
/HIFI /HIFI
/HIFI

-

-

X581

VB TACHO A VB I-BUS
-

-

X229
VB 30 RADIO VB R

X13016

0,5
BR

X1543

X18801

31E
19. Circuit diagram, on-board monitor wiring harness

EN/91

RADIO

19. Circuit diagram, on-board monitor wiring harness

Key
A196

On-board monitor

A197

Video module

N9

Radio

X229

Connector R

X581

Connector speedo A

X1362

Connector 58g

X1532

Radio/hi-fi navigation

X1543

Connector 30 radio

X6500

Plug-in connector adapter

X13016 Earth stereo/hi-fi
X18126 Radio A
X18344 Connector I-Bus
X18801 On-board monitor operating unit
X18802 On-board monitor
X18804 Video module A
X18805 Radio B

Colour abbreviations
BR =

brown

RT =

red

VI

=

violet

WS =

white

GR =

grey

SW =

black

GN =

green

GE =

yellow

BL =

blue

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/92

20. Circuit diagram, navigation system wiring harness

VIDEOMODUL
KAR-KBB
1
DFAVL

2
DFAV R

3

NAVI

RFL

A197

HIFI-KBB

NAVIGATION

X1310B

1

2

3

4

5

GND

RXD

CTS

RTS

TXD

X133185
NAVI

5

2

R

31

1
30

3

X1532B
NAVI

I-BUS

18
R75

17
B75

16
G75

8373297.9
MANTEL LTG.

0,35 0,35
GERT GEWS
DFAVL

10

DFAVR

11

0,35
WSGE

0,35
SCHIRM

0,35
WS

0,35
SW

0,35
RT

0,35
GR

0,35
VIRT

RFL

GND

RXD

CTS

RTS

TXD

R

1

15

16

14

13

12

3

8
SYNC

7

3

RGBGND VOICE

8373297.9
LTG. GESCH.

X1312
NAVI

12

1386697.9
LTG. VERDRILLT

0,5
RTGN

0,35
WSGRGE

0,35
RT

0,35
SW

0,35
GR

0,35
WS

0,5
0,35 0,5
SCHIRM BLRT BLBR

31

30

I-BUS

R75

B75

G75

SYNC

RGBGND VOICE

1

3

4

13

8

17

15

NAVI

VOICEGND

0,5
BRSW

10

X18806

9

VOICEGND

18

X1313
NAVI

A112
STG-NAVIGATION

F 39 0585 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/93

20. Circuit diagram, navigation system wiring harness

Key
A112

STG navigation

A197

Video module

X1310

KAR navigation

X1312

Navigation A

X1313

Navigation B

X1532

Radio/hi-fi-navigation

X18806 Video module A
X13318 Navigation/telephone

Colour abbreviations
BR =

brown

RT =

red

VI

=

violet

WS =

white

GR =

grey

SW =

black

GN =

green

GE =

yellow

BL =

blue

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/94

21. Circuit diagram, supplementary wiring harness for navigation system in
vehicles before production date 9/98

X10012

A52

1.0
BR

STG ABS/ASC

A3

Lichtmodul

MASSE-IVE
31
SA-LTG

9 (72)

42 (73)

DFAVL

DFAVR

38

RFSI

SA-LTG

X10117

X11374

SA-LTG

Schirm
SA-LTG

X1171

0.35
Schirm

0.35
WSGE

0.35
SW

0.35
GE

1724214.9
LTG. 2-ADR.
GESCH.

RFSI

DFVAL

DFAVR

S
31

3

1

2

4

X1310S
SA-LTG

Navigation
0.5
BR

X10305
MASSE SCHIRMLTG.
NAVIGATION
31
SA-LTG

F 39 0587 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/95

21. Circuit diagram, supplementary wiring harness for navigation system in vehicles before
production date 9/98

Key
A3

Light module

A52

Hydraulic unit ABS/ASC

X1171

ABS/ASC

X1310

KAR-Navigaion

X10012 Earth IVE
X10117 Black 54-pole socket housing of
the light module
X10305 Earth shield line Navigation
X11374 Connector shield
Only for automatic vehicles with M62 B44
engine and DSC, from production date
9/97 to production date 9/98, does the
DFAVL signal lie on PIN72 and the DFAVR
signal on PIN73 of the ABS/ASC control
unit plug X1171.

Colour abbreviations
BR =

brown

RT =

red

VI

=

violet

WS =

white

GR =

grey

SW =

black

GN =

green

GE =

yellow

BL =

blue

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/96

A65

ABS/DSC

A3

Lichtmodul

22. Circuit diagram, supplementary wiring harness for navigation system in
vehicles from production date 9/98

35

38

RFSI

X10117

DFAVL

18

DFAVR

X1170

X10184

X10183
VB DFAVL

0.35
GERT

0.35
WSGE

VB DFAVR

0.35
GERT

0.35
GEWS

0.35
GEWS

X001*

X002*

VB DFAVL

VB DFAVR

0.35
GEWS

0.35
GERT

RFSI

DFAVL

DFAVR

3

1

2

X1310S

Navigation

F 39 0586 B

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/97

22. Circuit diagram, supplementary wiring harness for navigation system in
vehicles from production date 9/98

Legende
A3

Light module

A65

Hydraulic unit ABS/DSC

X001*

Connector DFAVL

X002*

Connector DFAVR

X1170

black 42-pole connector of
hydraulic unit ABS/DSC

X1310S

black 6-pole pin housing

X10117

black 54-pole socket housing of
the light module

X10183

Joint connector DFAVL

X10184

Joint connector DFAVR

The items marked * are only valid for this
diagram. All other items and X-designations
correspond to the BMW customer service
circuit diagrams.

Colour abbreviations
BR =

brown

RT =

red

VI

=

violet

WS =

white

GR =

grey

SW =

black

GN =

green

GE =

yellow

BL =

blue

Retrofit/Installation Kit no.: 65 90 0 025 171 (for further information see front page)
Installation Instructions no.: 01 29 0 028 309

Date: 10.2000

EN/98